Product Catalogue

MG3710 Vector Signal Generator

Product picture

Quantity:

Description:

 The MG3710A Vector Signal Generator is a best-of-class, high-function, signal generator with excellent RF and baseband performance.

Technology applications:
- WiMAX
- WLAN
- LTE
- TD-SCDMA

Vector Signal Generator supporting frequencies of 100 kHz to 2.7/4/6 GHz
ACLR: -71 dBc (W-CDMA Test-Model 1 64DPCH, ≤+5 dBm)
Output level +23 dBm (CW, 400 MHz to 3 GHz)
Switching Time: ≤600 µs (List mode)
Two RF outputs using Dual-RF
Combines and outputs two modulation signals from one RF output using baseband addition function with easy setting and output of wanted and interference signals (modulated/delayed signals)
Built-in wideband (120 MHz) baseband signal generator

Up to two RF output connectors can be installed each with two built-in waveform memories to output two combined modulation signals from each RF connector for a maximum of four modulation signal outputs. A single MG3710A can output wanted + interference, wanted + delay, multicarrier, etc., signals, eliminating the cost of two normal generators while streamlining measurement setup and operation times.
It features a wide vector-modulation signal band and large waveform memories while supporting digital modulation signals for a wide range of communications modulation technologies. Not only is it the ideal measurement solution for key mobile communications methods, such as mobile phones, wireless LAN, etc., but it also has the performance required for developing new wideband wireless communications. With a built-in waveform pattern generator, any waveform pattern is easily selected to output modulation signals for every communications technology worldwide.


The following four types of waveform pattern can be used with the MG3710A

Built-in standard waveform patterns
Optional waveform patterns (sold separately) (MX3700xxA)
Waveforms generated by IQproducer waveform generation software (sold separately) (MX3701xxA)
IQ data generated by general-purpose signal-generation software and converted waveform patterns used by MG3710A

Features:

Basic Performance
Frequency Range: 100 kHz to 2.7GHz/4GHz/6GHz (1stRF Opt.032/034/036)
100 kHz to 2.7GHz/4GHz/6GHz (2ndRF Opt.062/064/066)
High Power Output: +23 dBm (CW, 400 MHz to 3 GHz)
SSB Phase Noise: <-131 dBc/Hz typ. (1GHz, 20kHz offset, CW)
ACLR: -71 dBc (W-CDMA Test-Model 1 64DPCH, ≤+5 dBm)
Switching Speed: <600 µs (frequency/amplitude, List/Sweep mode)


Baseband Performance
RF Band: Built-in,120 MHz baseband generator
Large 64 Msa waveform memory with optional expansion to 1024 Msa
Pre-installed standard waveform patterns
LTE-FDD/TDD (E-TM1.1 to TM3.3), W-CDMA/HSDPA, GSM/EDGE, CDMA2000 1x/1xEV-DO, Bluetooth®, GPS, PDC, PHS,
Broadcast (ISDB-T/BS/CS/CATV), WLAN (IEEE802.11a/11b/11g), Mobile WiMAX
Signal generation with waveform generation software (IQproducer)
LTE-FDD, LTE-TDD, WLAN 11a/b/g/n/j/p, Mobile WiMAX, W-CDMA/HSPA, cdma2000 1xEV-DO, TD-SCDMA, Fading,
Multi-Carrier, DVB-T/H, XG-PHS, TDMA


Expansion Options
AWGN Generator [Opt.049/079]
C/N: ≤40dB
BER Measurement Function [Opt.021]  
Input bit rate: 100 bps to 40 Mbps
USB Power Sensor (sold separately)
Supports connection of two USB power sensors max.
♦Frequency Range: 50 MHz to 6 GHz [MA24106A]
10 MHz to 18 GHz [MA24118A]
10 MHz to 26 GHz [MA24126A]
MIMO Signal Source: Supports local input [Opt-017]
Baseband clock, local and trigger signals can be shared between up to four MG3710A units to output phase coherency signals
synchronized with the signal output timing for configuring an 8x8 MIMO system.


back to product categories